Thermoelectric materials are special types of semiconductors that, when coupled, function as a “heat pump”.
The discovery of thermoelectricity dates back to Seebeck (1770-1831). Thomas Johann Seebeck was born in Revel (now Tallinn), the capital of Estonia which at that time was part of East Prussia. Seebeck was a member of a prominent merchant family with ancestral roots in Sweden. He studied medicine in Germany and qualified as a doctor in 1802. Seebeck spent most of his life involved in scientific research. In 1821 he discovered that a compass needle deflected when placed in the vicinity of a closed loop formed from two dissimilar metal conductors if the junctions were maintained at different temperatures. He also observed that the magnitude of the deflection was proportional to the temperature difference and depended on the type of conducting material, and does not depend on the temperature distribution along the conductors. Seebeck tested a wide range of materials, including the naturally found semiconductors ZnSb and PbS. It is interesting to note that if these materials had been used at that time to construct a thermoelectric generator, it could have had an efficiency of around 3% – similar to that of contemporary steam engines.
The Seebeck coefficient is defined as the open circuit voltage produced between two points on a conductor, where a uniform temperature difference of 1K exists between those points.
It was later in 1834 that Peltier described thermal effects at the junctions of dissimilar conductors when an electrical current flows between the materials. Peltier failed however to understand the full implications of his findings and it wasn’t until four years later that Lenz concluded that there is heat adsorption or generation at the junctions depending on the direction of current flow.
In 1851, Thomson (later Lord Kelvin) predicted and subsequently observed experimentally the cooling or heating of a homogeneous conductor resulting from the flow of an electrical current in the presence of a temperature gradient. This is know as the Thomson effect and is defined as the rate of heat generated or absorbed in a single current carrying conductor subjected to a temperature gradient.
It was later in 1909 and 1911 that Altenkirch showed that good thermoelectric materials should possess large Seebeck coefficients, high electrical conductivity and low thermal conductivity. A high electrical conductivity is necessary to minimise Joule heating, whilst a low thermal conductivity helps to retain heat at the junctions and maintain a large temperature gradient. These three properties were later embodied in the so-called figure-of-merit, Z. Since Z varies with temperature, a useful dimensionless figure-of-merit can be defined as ZT.
Although the properties favoured for good thermoelectric materials were known, the advantages of semiconductors as thermoelectric materials were neglected and research continued to focus on metals and metal alloys. These materials however have a constant ratio of electrical to thermal conductivity (Widemann-Franz-Lorenz law) so it is not possible to increase one without increasing the other. Metals best suited to thermoelectric applications should therefore possess a high Seebeck coefficient. Unfortunately most possess Seebeck coefficients in the order of 10 microvolts/K, resulting in generating efficiencies of only fractions of a percent.
It was during the 1920’s that the development of synthetic semiconductors with Seebeck coefficients in excess of 100 microvolts/K increased interest in thermoelectricity. At this time it was not apparent that semiconductors were superior thermoelectric materials due to their higher ratio of electricall conductivity to thermal conductivity, when compared to metals.
As early as 1929 when very little was known about semiconductors, Abram Fedorovich Ioffe (1880-1960) showed that a thermoelectric generator utilising semiconductors could achieve a conversion efficiency of 4%, with further possible improvement in its performance. By the 1950’s, Ioffe and his colleagues had developed the theory of thermoelectric conversion, which forms the basis of all modern thermoelectric theory.
A large number of semiconductor materials were being investigated by the late 1950’s and early 1960’s , several of which emerged with Z values significantly higher than in metals or metal alloys. No single compound semiconductor evolved that exhibited a uniform high figure-of-merit over a wide temperature range, so research focused on developing materials with high figure-of-merit values over relatively narrow temperature ranges. Of the great number of materials investigated, those based on bismuth telluride, lead telluride and silicon-germanium alloys emerged as the best for operating to
temperatures of about 450K, 900K and 1400K respectively.
The simplest thermoelectric generator consists of a thermocouple, comprising a p-type and n-type thermoelement connected electrically in series and thermally in parallel. Heat is pumped into one side of the couple and rejected from the opposite side. An electrical current is produced, proportional to the temperature gradient between the hot and cold junctions.
If an electric current is applied to the thermocouple as shown, heat is pumped from the cold junction to the hot junction. The cold junction will rapidly drop below ambient temperature provided heat is removed from the hot side. The temperature gradient will vary according to the magnitude of current applied.
A typical thermoelectric module is shown left. The module consists of pairs of p-type and n-type semiconductor thermoelements forming thermocouples which are connected electrically in series and thermally in parallel.
- In cooling mode, an electrical current is supplied to the module. Heat is pumped from one side to the other (Peltier effect), the result is that one side of the module becomes cold.
- In generating mode, a temperature gradient is maintained across the module. The heat flux passing through the module is converted into electrical power (Seebeck effect).
http://www.its.caltech.edu/~jsnyder/Research.html
http://www.its.caltech.edu/~jsnyder/thermoelectrics/science_page.htm
http://www.americool.com/BeyondBismuthTelluride2003.htm
A III Reunião Ibérica de Colóides e Interfaces irá ser realizada em Granada, Espanha, de 13 a 15 de Julho de 2009.
Discover8 is a new scientific communications database where registered users can suggest, comment and rate scientific communications. Its also possible to recommend any article with a valid web link (for instance your own articles 
).
The meeting is being organized by the National Division of Catalysis and Porous Materials of the Portuguese Chemical Society and is going to be held in Lamego, Portugal, from 21 to 23 September, 2007.
